Tag Archives: smithing

smithing – creation of a pair of gemstone and sterling silver earrings

Lots of people like to know the process behind the creations I produce, and I sometimes forget – just because I know how I do this, doesn’t mean everyone does! These lovely dangly gemstone earrings were a wedding gift from my friend and client Natasha to a dear friend of hers.

Natasha found these sparkly amethyst, Rose de France and aquamarine rose cut cabochons in my gemstone collection.

First I shaped the bezels. A bezel is the part that goes around the stone and holds it in place on the piece. I take a strip of silver, bend it into shape with my half round pliers, and solder the join. Once the bezels have been immersed in pickle (an acid solution) to remove the buildup of borax and the oxidisation, I rinse and dry them and hammer them into shape with a mallet on my ring mandrel.

I solder the bezels onto a silver backing plate. After I pickle, file and emery the bezel settings, I check that the stones all fit nicely into their little housings.

Then it’s time to add some links to join the bezels together. I create the links, line them up and solder them on.

I add the ear wires. As always, I am amazed that something that looks so unappealing will soon become something beautiful!

After some more cleaning up, I mount the earrings in sealing wax to hold them still while I set the stones with my engraving ball and chasing hammer.

After yet more emerying and finishing, the earrings are ready to go off to their new home!

In case you want more, I have written before here, here here and here about my processes. Happy reading!

smithing – creation of a freeform gemstone and sterling silver ring

I always love to see behind the scenes of manufacturing – maybe it all stems from that cool crayon factory clip that used to be on Sesame Street? One of my gorgeous clients, Natasha, asked me to use this charoite in a ring for her mum, and her mum was interested to see the work in progress. I have written before here, here and here about my processes, and I thought you might like to see some more!

It started with this luscious piece of charoite which Natasha spotted in my gemstone collection. Using a strip of silver and my trusty half round pliers, I made a bezel for the stone.

I fitted the stone to a piece of sheet silver.

After sawing out the shape of the backing plate, I prepared to solder.

After soldering, the silver becomes oxidised and it seems far-fetched that this will ever turn into something beautiful!

Some careful measurement, and more bending with my half round pliers, and a ring shank is made.

A quick check that the stone fits properly, then I’m ready to solder the shank to the top.

The shank is lined up on the top, and soldered firmly in place.

Time for lots of filing and emerying to get the silver ready for the stone to be set.

After plenty of time with my engraving ball and chasing hammer, the finished product!

smithing – creation of a gemstone and sterling silver pendant

It’s always a joy to see other people’s creative techniques. I have written before here and here about the process of silversmithing, and I thought you might like another little insight into this world.

First, the drusy gemstone (from my never-ending collection!) and a rough design sketch. I’ve already created the bezel (the metal that wraps around the stone) in this picture, bending a straight strip of metal (like the one pictured) around the stone.

The next step is preparing the backing plate. He’s some sawing and filing in action.

After filing, comes emerying.

And laying out the component parts to see how it will look. The balls of silver are made by heating some little pieces of silver until they melt – the molten silver naturally gathers up into a sphere. It’s fun stuff!

I emery the back of the bezel flat, so that the join between the two pieces of metal will be exact and the solder will flow correctly.

Then it’s time for a bit of heat.

I love how from this dirty blackened thing comes an object of beauty!

Into a solution of sulphuric acid to remove all the oxidization etc.

While the piece is pickling, I create the bail (the part from which the pendant will hang), and a little plate stamped with my maker’s mark and ‘925’ to show the piece is made from sterling silver.

Those are soldered onto the piece, then it’s back in the pickle and after that, a rinse off.

After a good clean-up, with lots of emerying down to a fine grade, I mount the piece on a wax dop so that i can set the stone.

My engraving ball comes in super-handy here!

Some time with my chasing hammer, and the stone is set.

And finally, the finished piece!

If you like this pendant, you can see more of it here in my shop.

smithing – creation of a teardrop shaped gemstone and sterling silver ring

I love seeing other people’s processes, and I thought it was time to give you all another look into what goes on in my workshop. I have blogged before about how I create one of my signature big chunky rings, and I thought it was time to examine that process again. Here’s how I do it!

Firstly, an appropriate width strip of sterling silver sheet .6mm thick is selected.

This is curved by hand using a pair of half round pliers to fit the gemstone.

Next, the strip is cut to approximately the right length on my bench peg using my jeweller’s saw, leaving a small extension for soldering against.

In this video, you see me prepare and apply the borax, position the solder (not usually quite so fumbly, I had a bit of stage fright!) and solder the bezel together.

Once the metal is cool, it goes into the pickle to be cleaned. An explanation of pickle can be found in my previous blog post.

I trim the excess bezel metal away from the solder join.

I check to make sure the bezel is a good fit.

I emery the bottom of the bezel so that it is completely flat and will make a good join with the base plate.

I select a piece of 1mm thick sterling silver sheet to fit the bezel.

I solder the bezel to the backing plate. Here you see me applying the paillons of solder with borax, and soldering the join. Then it’s back to the pickle.

After rinsing and drying, a bit of a check to see how it’s looking!

Now, I saw the excess metal from around the bezel setting.

After filing the edges of the bezel setting, I start creating the ring shank.

Using the appropriate width of 1.2mm thick sterling silver plate, I bend the shank to the right shape and size.

I trim the shank to the right length.

I hammer the shank with a mallet to get it perfectly round (this shot is for explanation only, I actually have the mandrel hard up against the bench to absorb the force when I’m really hammering the ring!).

Emerying the inside of the shank with my flex drive makes life easier.

After more filing and emerying, I stamp the inside of the shank with my maker’s mark and 925, which marks the metal as being sterling silver (the 92.5% is the fine silver content).

I solder the shank to the bezel setting assembly.

Then it’s time for plenty more filing, and coarse to fine emerying to bring the ring close to it’s finished state. (Zen or tedium, you decide!)

Next, I head over to my trusty engraving ball to set the stone.

Plenty of gentle hammering with my setting hammer later…

And my work, bar some tidying up, is done!

There it is, a beautiful drusy agate ring. I do so love what I do!

smithing – handcrafting a sterling silver spiral chain

The process of creating is sometimes more intricate than you might think when looking at the final object, so I thought we’d take a look at how chain is handmade.

To start, I use some lengths of wire (which is made by rolling a block of silver repeatedly in the same direction through a rolling mill, until it is thin enough to draw through a draw-plate down to the right dimension).

After annealing the wire (a process where the wire is heated to a dark red to line the molecules up, making the silver malleable), I pickle it, by placing the metal in an acid solution to remove any oxidisation, dirt, or flux.

I then wrap it around a steel post of a suitable diameter (this tool is called a jump ring maker, and comes with steel posts of varying widths).

Once the wire is wrapped into shape, I remove it from the steel rod.

I saw each link with a jeweller’s saw.

Each link is individually created.

After a tidy up of the links if required, I join them together, in this case in a specific mathematical combination. (I love how science, maths and creativity collide!)

Once all the links are joined, I make sure the chain is the correct length.

Then I solder each link closed. Yes, each and every link! In this case, that means around two hundred and eighty links to be made, joined and soldered individually.

Once that is complete, the final links are added which join the chain together in a specific way to create the spiral effect. Then it’s back in the pickle for another bath, followed by some time in the tumbler, to polish and harden the chain. (I’ll post about my tumbler another day, I promise!)

The finished product is quite spectacular, IMHO. You can see more pics of this twisted spiral chain technique being used here and here. I love what I do!

the silver forge

jewellery handcrafted by ruthie gray